Enter your e-mail address below to have your password reset. You will receive an e-mail with a new temporary password in it.
Your new password is on its way. If you have problems accessing your account, please contact us at 1-888-757-4774 and we'll help you out.
I'm sorry, your e-mail was not found in our system.
If you think this is a mistake, please contact customer service at 1-888-757-4774 or via e-mail here.
Sign in to access your account and complete your order.
You will have the option to create an account on the order confirmation page.
Air Eliminators play a crucial role in hydronic heating systems. An air eliminator should be installed to insure the initial and continual removal of air from hydronic heating systems. The air elimination device should be installed between the heat source supply outlet and the circulator pump. The Spirovent Air Eliminators, Vortech Air Eliminators, Taco Air Scoops, and the Taco 4900 Series are all adequate air removal products.
Spirotherm Air Eliminators are designed for use in Hydronic Heating Systems. The Spirovent Junior Air Eliminator comes in 3/4", 1", 1-1/4", and 1-1/2".
The Taco VorTech Air Separator is designed to provide an enhanced level of air removal in hydronic heating, cooling or combination systems. Taco's innovative tangential flow pattern, primary separation chamber and standard Taco Hy-Vent make the VorTech the most effective and reliable air separator you can buy.
The special design of Watts & Taco Air Scoops slow water velocity to separate the air from solution. Air Scoops efficiently remove air to provide noiseless, air-free hydronic heating, cooling or combination systems. These air scoops come in several different sizes, and are the signature green color.
The Taco 4900 Series Air Separators help you save money and prolong the life of system pumps, piping and components by removing air and dirt from the system to prevent reduced heat transfer, loss of efficiency, pipe corrosion, pump damage, increased energy consumption, and irritating noise.
As system fluid enters through the inlet, (either straight or angle) the diffuser distributes flow evenly across the stainless steel, wire brush-like medium. Air bubbles, even micro air bubbles, stick to the brush filaments. Trapped air rises above the diffuser through a baffle where the air is then released through an opening at the top. Deareated water then goes back into the system.
Bell & Gossett has introduced the EASB-JR, a micro-bubble air separator that makes both residential and commercial hydronic heating systems more efficient, operate quieter, and last longer. Featuring a brass body and stainless steel internal components, the EASB-JR Air Separator is designed to automatically remove entrained air bubbles in hydronic systems. As fluid enters the air separator, the velocity is decreased creating a low-pressure area. The small bubbles are released from fluid and then collect on the coalescing medium. As the bubbles coalesce, they rise to the top of the air separator where they are released to atmosphere through the built-in automatic air vent.
The Spirotrap Dirt Separator employs a patented Spirotube® barrier medium that dirt particles collide into. Simple to install with a straight in-line design it is available in the Junior Series for residential and light commercial applications from 3/4" to 1-1/2" pipe size. Solid brass construction with ball valve included.
The B&G In-Line Air Separator is specifically designed to efficiently separate air from circulating water in hydronic heating and cooling systems to assure quiet operation.
Airtrol Tank Fittings help establish the proper initial liquid level in the compression tank when filling the hydronic system. They help maintain proper system pressurization by directing released air to the compression tank during system operation and permit cooler liquid flow to the boiler during the off cycle as system liquid cools. Airtrol Tank Fittings must be used with the appropriately sized In-Line Airtrol or Rolairtrol air separator.
The Spirovent Air Eliminator / Dirt Separator employs a patented Spirotube coalescing / barrier medium that scrubs the air from the system fluid and gives the dirt something to collide into. Simple to install with a straight in-line design it is available in the Dirt model as a sealed vessel and the Drain model that includes a removable head and tube sheet construction. This allows access to the Spirotube bundle for inspection or cleaning.
Conventional automatic air vents installed in Hydronic heating systems can leak and cause inefficient system operation. To effectively eliminate air from the system without bleeding, air bubbles ned to be vented. The NEW Honeywell SuperVent purges air through a no clog vent assembly that controls dirt and debris to minimize air vent fouling.
Series AS-MB Microbubble Air Separator is designed for efficient separation and elimination of entrained air in hydronic heating systems. No minimum inlet/outlet piping length is required for proper operation. This series features a durable brass body construction, corrosion-resistant polyphenylsulfone (PPSU) coalescing media that withstands petroleum based cleaners, glycol anti-freeze and temperatures up to 240 degrees F and a fully serviceable design for inspection and cleaning.
This category contains a variety of Caleffi Separators including DISCALDIRT Air & Dirt Separators, DIRTCAL, Hydro Separator series.
An air eliminator removes unwanted air from a hydronic heating system. Air can trap vapor in a hydronic heating system which will damage pipes and system components. Air can also create irritating noise and increased energy consumption. An air eliminator will reduce air in your heating system which will allow for quiet operation and minimize costs.
As water temperature increases, pressure decreases. As pressure decreases, air is released from the water. Therefore, an air eliminator should be installed in the hottest part of a heating system -- between the boiler's supply outlet and a circulator pump.
SpiroVent air eliminators are among the most popular purchased at PexSupply.com. Water entering a SpiroVent contains a mixture of air and water. The mixture collides with the Spirotube within the SpiroVent. The air rises to the top and lowers the water level. The air is then released from a vent cap located at the top of the Spirovent. SpiroVent air eliminators are superior to most air elimination devices on the market.
Dirt separators remove dirt particles from a hydronic system. This is important because even the smallest particles can cause huge problems in the system. Dirt separators are more effective and lower maintenance than filters. Filters become blocked over time, leading to pressure drops. Dirt separators reduce malfunctions, wear and tear, and maintenance cost.
At PexSupply.com, we offer a wide selection of Spirotherm, Taco, and Bell & Gossett air eliminators to suit all of your hydronic heating needs.
Subscribe to our Channel
Like Us on Facebook
Visit Our Blog
At PexSupply.com, our goal is to bring you the highest quality plumbing, heating and HVAC supplies at competitive prices. Our product catalog includes PEX Plumbing Supplies, Radiant Heat Supplies, VisionPro Honeywell Thermostats, Taco pumps and mini-split air conditioners. If there are items you are looking for but can't find on our website, please contact our Customer Service Representatives & we will do our best to find what you need.
© 2013 PexSupply.com