Enter your e-mail address below to have your password reset. You will receive an e-mail with a new temporary password in it.
Your new password is on its way. If you have problems accessing your account, please contact us at 1-888-757-4774 and we'll help you out.
I'm sorry, your e-mail was not found in our system.
If you think this is a mistake, please contact customer service at 1-888-757-4774 or via e-mail here.
Sign in to access your account and complete your order.
You will have the option to create an account on the order confirmation page.
Radiant Heat Panels will improve the efficiency of a radiant heat system. These panels include Wirsbo Quik Trak which can be used above a subfloor, and Wirsbo Joist Trak which should be placed in between the joists below the space to be heated.
Joist Trak Panels are manufactured by Uponor Wirsbo. These Wirsbo Joist Trak Radiant Heat panels are made from thick aluminum alloy and provide excellent heat transfer to the space above. They are attached beneath the wood subfloor in Radiant Heat Systems. How many pieces of joist trak do I need? For 8" on-center spacing, multiply the net area to be heated by 1.5. Take the total tubing number and multiply it by .85. Divide this number by four. This will tell you how many Joist Trak Panels you will need. For Example, if we have a room that is 400 sq ft., multiply it by 1.5, you will need 600 feet of tubing assuming 8" on center. you will then need to multiply 600 by .85, which gives you 510. 510 divided by 4 is 127.5. So you will need approximately 128 Joist Trak Panels. When installing Joist Trak, leave 1-2" between panels.
The 1/2-inch Wirsbo Quik Trak plywood panels are attached to an aluminum heat transfer sheet. To determine the number of pieces of Quik Trak you need, multiply the square feet of the space to be heated by .386. Quik Trak Return Panels are designed with a 'U' groove to complete tubing turns. The half-moon grooves are attached to the panels. Each return panel is shipped with a separate aluminum sheet for installation beneath the panel. To determine the number of return trak panels you need, multiply the square feet of the space to be heated by .043. All Quik Trak Panels measures 7" wide x 48" long. Use with Wirsbo 5/16" hePEX plus only. The Quik Trak Sealant is 100% silicone and adheres to PEX tubing in Quik Trak groove and provides good thermal transfer. Approximately 1 bottle of Sealant should be used for each loop. The 1-1/4" screws are designed specifically for Quik Trak installations using 3/4" subfloors.
Radiant heat has never been easier or more affordable for your home than with the Ultra-Fin Radiant Floor Heating System™. Take a leap forward with Ultra-Fin – the radiant heat system that provides the comfort and efficiency you want from radiant floor heating, while providing simpler installation for a greater variety of home styles.
Radiant heat is growing in popularity, and is now the preferred heating system in new homes. Radiant heat provides more comfort throughout the home than standard baseboard heat. PEX tubing is installed beneath the floor and heats the home from the ground up. As the floor becomes warm, the room is heated evenly and efficiently. Radiant heat is silent, producing no creaking, banging, or humming sounds, such as those commonly heard in other heating systems. Radiant heat allows the thermostat to be set a few degrees lower than it would normally be set, while still providing the same warmth. This cuts energy bills and saves you money.
Joist Trak Panels
Uponor (Wirsbo) Joist Trak is the best option when an existing floor is in place, but access to the joist spaces beneath them is still available. Joist Trak panels are made of a thick aluminum alloy which is great for heat transfer. These aluminum panels contain 1/2" grooves that allow 1/2" PEX tubing to be installed firmly into place. Joist Trak panels heat up as hot water passes through the PEX tubing. The aluminum panels are installed securely in joist spaces beneath the wood subfloor and transfer heat to the floor above. To determine the amount of Joist Trak and PEX Tubing needed for your project use the Joist Trak Calculator.
Ultra-Fin radiant panels are aluminum plates similar to Joist Trak panels. They are also installed in joist spaces beneath the wood subfloor and transfer heat to the floor above. Ultra-Fin panels are not installed directly to the joists. Instead, they are hung 2" beneath the wood subfloor which creates convection. 1/2" PEX tubing is used with Ultra-Fin panels.
Uponor (Wirsbo) Quik Trak is best when a foundation is present and you can raise your floors by 1/2" but not 2". Quik Trak panels are wooden panels that contain an aluminum heat transfer plate on one side, and grooves that allow 5/16" PEX tubing to be installed firmly into place on the opposite side. Similar to a Joist Trak panel, a Quik Trak transfer plate heats up as hot water passes through the PEX tubing. These unique panels are available in straight runs or return bends to create loops. They can easily be cut or combined to fit the size and shape of any room.
Subscribe to our Channel
Like Us on Facebook
Visit Our Blog
At PexSupply.com, our goal is to bring you the highest quality plumbing, heating and HVAC supplies at competitive prices. Our product catalog includes PEX Plumbing Supplies, Radiant Heat Supplies, VisionPro Honeywell Thermostats, Taco pumps and mini-split air conditioners. If there are items you are looking for but can't find on our website, please contact our Customer Service Representatives & we will do our best to find what you need.
© 2013 PexSupply.com