Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord Zoom

Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

SKU:ETC-111000

Brand: Ranco

Ranco
Qty Price
$49.45
/ each
$234.75 / box (5 units x $46.95)
In Stock! Usually Ships in 24-48 Hours
67 Available

Specs

Application: Remote Bulb Temperature
Temperature Range: -30° to 220°F
Differential:
?
1° to 30°F
Voltage:
?
120v
240v
208v
Sensor: Thermistor
Bulb Size: 2" x 1/4"
Capillary Length: 8 ft.
Operating Temp Range: -20° to 140°F
Enclosure Type: NEMA 1 Enclosure
Height: 6.52"
Width: 2.7"
Depth: 2.48"
Switch Action: SPDT
Humidity Range: 0 to 95% RH (Non Condensing)
Contact Ratings 120v: 16.0 AFL
96.0 ALR
Contact Ratings 240v: 8.0 AFL
48.0 ALR
Resistive: 15 A
8 A
Horse Power:
?
1
Pilot Duty Rating: 125 VA
Stages:
?
One

Description for Ranco ETC-111000

Digital Display

  • Unlike many electronic controls, the ETC is simple to install and set up. One finger is all you need to program it. The standard digital display and keypad allow the user to adjust the temperature settings with 1 degree resolution. Setpoint temperature, differential and mode of operation (heating or cooling) can all be selected using the keypad and display.
    When not in the programming mode, the display gives a constant readout of the sensor temperature. Annunciators on the liquid crystal display also indicate when the relay is energized.

Remote Temperature Sensing
  • The ETC is capable of remote temperature sensing up to 400 feet away from the control when using standard 22 gauge sensor wire.

Built-In Safety
  • Every ETC model is equipped with diagnostic programs that check for hardware, software, or system problems and display different error codes to indicate where the trouble is.
    The ETC also has a keyword lockout switch to prevent tampering with the control settings by unauthorized personnel. The switch, which is located inside the enclosure, can be used to disable the keypad function.

Specifications
  • Temperature Setpoint Range: -30° to 220°F
  • Differential Range: 1 to 30 Degrees F
  • Input Power Requirements: 120/208/240 VAC
  • Sensor: Thermistor, 2" long x 1/4" Diameter, with 8' cable
  • Control Ambient Temperatures: Operating (20-140), Storage (40-176)
  • Ambient Humidity: 0 to 95% RH, non-condensing
  • Enclosure: NEMA 1
  • Dimensions: 6.52" high x 2.7" wide x 2.48" deep
  • Agency Approvals: UL Listed, CSA Certified
  • Switch Action: SPDT

Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

REVIEW SNAPSHOT®

by PowerReviews
Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord
 
4.8

(based on 54 reviews)

Ratings Distribution

  • 5 Stars

     

    (47)

  • 4 Stars

     

    (6)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (1)

  • 1 Stars

     

    (0)

98%

of respondents would recommend this to a friend.

Most Liked Positive Review

 

Super Easy

I have this running a chest freezer I turned into a "keezer". The instructions are clear and it is easy to program. Only minor wiring skills are needed to hook th...Read complete review

I have this running a chest freezer I turned into a "keezer". The instructions are clear and it is easy to program. Only minor wiring skills are needed to hook this up. If you have ever wired a outlet or light switch, you can wire this.

VS

Most Liked Negative Review

 

Difficult to wire

It appears that the design of the blocks for the cable connections inside of the control have changed. It is difficult to insert and correctly tighten the cable into the blocks, because the openings ...Read complete review

It appears that the design of the blocks for the cable connections inside of the control have changed. It is difficult to insert and correctly tighten the cable into the blocks, because the openings of their metal inserts are now recessed and not visible anymore.

REVIEWS

Reviewed by 54 customers

Sort by

Displaying reviews 1-10

Back to top

Previous | Next »

1/24/2012
 
5.0

perfect for this application

By wood burner

from Thompson ct

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I installed unit on my hydronic heater to controle over temp. it now turns on the heat exchanger if temp goes too high due to thermostat not calling for heat. no more over temp issues

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

1/24/2012
 
4.0

Good Product

By Bo6

from Comox BC

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I use the controler for a hot box for waxing skis. The large drift settign is usefull to automatically cool then reheat the skis.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

12/26/2011
 
5.0

Works just like the first

By UP Scott

from Phoenix, AZ

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I have had one of these controllers for about 8 years now and the first one just started having problems. I ordered another of the same for a replacement to run my hot water circulation pump and it work great. I use it to cycle the pump on and off after the water is up to temp.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

11/30/2011
 
4.0

Affordable, easy to use

By Guest

from NE Ohio

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

Likes: relatively inexpensive, easy to program

Minor dislikes: wiring diagram could be a little unclear for someone inexperienced

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

11/29/2011
 
5.0

GREAT PRODUCT, GREAT PRICE

By Joel

from Fountain, MN

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

This product is easy to use, easy to wire. I have used this product before and will use it again. The price of this product makes it a great replacement for other temperature switches.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

11/23/2011
 
5.0

Excellent Thermostat

By Wilson

from Georgetown, SC

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I am replacing my thermostats with the Ranco. It is accurate and I can set the differential as I want. I use it for a hot water loop control; another is used for a fan control; and the third is used to control a hot water heater.

This is a great product

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

10/29/2011
 
2.0

Difficult to wire

By Hawk

from Baldwin, NY

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

It appears that the design of the blocks for the cable connections inside of the control have changed. It is difficult to insert and correctly tighten the cable into the blocks, because the openings of their metal inserts are now recessed and not visible anymore.

Bottom Line No, I would not recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

9/29/2011
 
5.0

Awesome Temperature Controller

By Shawn the Brewer

from Augusta, GA

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I bought this product recently to turn my freezer into a fermentation chamber since I'm living in Georgia. It worked great! I was even able to mount the controller onto the back of my freezer for that clean professional installed look.

The only bad thing is the instructions can be a little confusing for a first timer wiring up something, however there are plenty of instructions on the internet to help you find your answer.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

8/10/2011
 
5.0

"I would buy this product again and agai

By Bluesuede Poultry

from Albertville Alabama

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I used this for incubator thermostat and it works perfectly. I can set the temp and it kicks off exactly at the right temp and kicks on within 1 degree variance.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

8/3/2011
 
5.0

It worked fine when I tested it

By greg

from Mountain View, CA

Verified Buyer

Comments about Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord:

I bought this to control the temperature in a sausage smoker. It looks like a very good quality piece of equipment. The instructions that came with it were extremely clear. I have tested it but haven't used it in the actual smoker yet. It worked flawlessly in the test.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

Displaying reviews 1-10

Back to top

Previous | Next »

Q&A: Ask the Questions, share answers

Do you have questions about this product?

get answers from real customers and in-house experts with AnswerBox.

6 Questions | 13 Answers
Displaying questions 1-6
  • Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

    Q:

    can the probe be replaced? how hard is it to do this and what is the cost for a replacement probe?
    Asked on 9/23/2011 by Anonymous

    2 answers

    • CUSTOMER CARE

      A:

      The sensor can be replaced (part 1309007-044). See the following manual for installation instructions: http://s3.pexsupply.com/manuals/1253196590775/17484_PROD_FILE.pdf

      Answered on 9/23/2011 by PexSupply Staff from NY

    • VERIFIED BUYER

      A:

      Yes. According to the data sheet with the controller, you can get a replacement temp probe. The sheet lists the type and characteristics of the thermister used. If you wanted to replace it with a different type, (shape, housing, etc.) you could as long as it matches the original used.

      Answered on 12/26/2011 by UP Scott from Phoenix, AZ
  • Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

    Q:

    I'd like to use this to keep the temperature in our fridge around 65-70 degrees but am wondering what happens to the freezer portion if I plug the unit into this? Does the freezer compressor only come on when the fridge kicks on? Is there any way to keep the freezer portion frozen and the fridge portion temperature controlled? Thanks!
    Asked on 5/13/2011 by Anonymous

    1 answer

    • CUSTOMER CARE

      A:

      We recommend that you contact the manufacturer of your refrigerator. It is possible that the this thermostat would turn off the freezer as well.

      Answered on 5/17/2011 by PexSupply Staff from NY
  • Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

    Q:

    Does this unit come with a power cord? I don’t see one in the picture, or in any of the specs
    Asked on 4/16/2011 by Joe from Ohio

    2 answers

    • CUSTOMER CARE

      A:

      Power cord is not included; you must supply your own. The following video may contain some useful information: http://www.youtube.com/watch?v=peoL_dcHaU

      Answered on 4/18/2011 by PexSupply Staff from NY

    • VERIFIED BUYER

      A:

      This unit does not come with a power cord.

      Answered on 4/21/2011 by Blaze from Canada
  • Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

    Q:

    we put the sensor with about 18in of the cord in the water on our wood water furnace in about 2 months the sensor gave a ep code we know the water wasn't 225deg. do we need to put this in a bulb well and do you have one?will it still sense as well?
    Asked on 4/14/2011 by Anonymous

    1 answer

    • CUSTOMER CARE

      A:

      According to the manufacturer, these sensors should not be submersed in any liquid. You would need to use a thermal/bulb well. The only ones we have are parts 121371A, 121371B, and 121371M.

      Answered on 4/15/2011 by PexSupply Staff from NY
  • Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

    Q:

    I can't read the numbers on the display screen? It's all black.
    Asked on 10/10/2010 by Miranda from Wisconsin

    6 answers

    • CUSTOMER CARE

      A:

      This can be a power problem. We recommend checking the incoming voltage and ensure there is power. If you need further assistance, we recommend contacting the manufacturer for additional technical support.

      Answered on 10/11/2010 by PexSupply Staff from NY

    • A:

      Did it get wet? Sounds like the screen is simply dead. It's never happened to me, and I don't know of any way to change it. (By the way, dumb point, but if for some reason you are using this in an area with bright light, make sure you are not trying to look at it through polarized lenses, like for sunglasses -- that can cause LCD "blackout" too.)

      Answered on 1/22/2011 by Fermenting from Minneapolis

    • VERIFIED BUYER

      A:

      It could be several things. LCDs will go all black if they get too hot. Once they cool down, they will be fine. It could also be defective. LCDs can freeze too. If they freeze, the display seal (yes, that's where the 'liquid' part of the name comes from) may break and then it's all over for the display...

      Answered on 1/29/2011 by Involuntary plumber. from Boston, MA

    • VERIFIED BUYER

      A:

      excessive heat from direct sunlight can overheat the display and cause it to go black. When the unit cools down, then display should return to normal. LCD screens are susceptible to heat.

      Answered on 3/5/2011 by hmca from Lafargeville, NY

    • VERIFIED BUYER

      A:

      It's most likely not wired correctly.... http://www.youtube.com/watch?v=peoL_dcHaU8
      This is a link to a instructional vid and wiring diagram.

      Answered on 2/26/2011 by Phil the snake man from San Andreas, CA

    • VERIFIED BUYER

      A:

      Perhaps you don't have power to the unit. Check input voltage with a basic 120/240 volt check light and check to see that you have it connected correctly. If it all checks out perhaps you have a faulty unit.

      Answered on 4/7/2011 by Boss from Cedar City, UT
  • Ranco Single Stage ETC Temperature Control w/ Sensor (120/240V Input) - Includes 8' Cord

    Q:

    My 111000-000 is not operating.

    It continues to give the " E2 " Message.

    Can I REPROGRAM it myself ?
    Where or how can I get that information?

    Many Thanks ,again
    C.C. OURSO
    Asked on 8/27/2010 by C.C. from Baton Rouge, La.

    1 answer

    • CUSTOMER CARE

      A:

      The E2 message is a memory error. You can press the "Set" button to go through all the settings. If the unit continues to show E2 then you will need to replace the unit. You can refer to this Owner's Manual for additional information http://s3.pexsupply.com/manuals/1283530359689/38736_PROD_FILE.pdf

      Answered on 9/3/2010 by PexSupply Staff from NY
Displaying questions 1-6

Do you have a question about this product? 

Free Shipping on orders over $300

You May Also Want

PexSupply.com Logo

Join Our Mailing List - Sign up and receive special offers and coupons

Nextag Seller PriceGrabber User Ratings for Pex Supply Pexsupply is Become.com Trusted Merchant BBB Reliability Seal
HACKER SAFE certified sites prevent over 99.9% of hacker crime. Facebook Twitter Youtube