3/4" Red PEX Tubing (300 ft Coil) Zoom

3/4" Red PEX Tubing (300 ft Coil)

SKU:075-300-R

Brand: Rifeng

Rifeng
Qty Price
$118.85
/ each
$338.55 / box (3 units x $112.85)
In Stock! Ships in 24-48 Hours
59 Available

Specs

Size: 3/4"
Color: Red
Length: 300 ft.
Inside Diameter: 0.671"
Outside Diameter: 0.875"
Material: PEX
Grade:
?
PEX-b
Application: Plumbing
Tubing Type: Non-Oxygen Barrier
Warranty: 25 Years

Description for Rifeng 075-300-R

Rifeng PEX pipe is produced with crosslinked polyethylene. Crosslinking is obtained through a chemical process that increases the bonds between macromolecules to form a more complex structure than the normal polyethylene. Due to the crosslinking, the polyethylene's performance is greatly enhanced and maintains the excellent properties of thermoplastics. Offering excellent corrosion resistance, incredible flexibility and unusual toughness, Rifeng PEX pipe allows for fast and easy installation.

3/4" Red PEX Tubing (300 ft Coil)

REVIEW SNAPSHOT®

by PowerReviews
Rifeng1" Blue PEX Tubing (100 ft Coil)
 
4.9

(based on 35 reviews)

Ratings Distribution

  • 5 Stars

     

    (30)

  • 4 Stars

     

    (5)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

100%

of respondents would recommend this to a friend.

Reviewed by 35 customers

Sort by

Displaying reviews 1-10

Back to top

Previous | Next »

4/11/2012
 
5.0

Anyone can do it

By brian

from NC

Verified Buyer

Comments about 1/2" Red PEX Tubing (100 ft Coil):

One run with a few small bends and it was done, crimped the ends to the plumbing and i felt like i was real plumber. it was so easy and quick i will be redoing the rest of the house with the product when needed.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

2/14/2012
 
5.0

Link for radinat heating system to solar

By SolarNrgMan

from Washington DC

Verified Buyer

Comments about Rifeng 1" Red PEX Tubing (100 ft Coil):

I used this high temperature PEX 1" tubing to connect a solar heated storage tank and a Navien CH240 backup heater that is located on the fourth floor of the town house while the radiant floor is on the first floor. Just what the doctor ordered. Simple and easy to install inside sheet rock wall without insulation needed.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

2/5/2012
 
4.0

Converted the whole house to pex

By Charles H

from NE PA

Verified Buyer

Comments about 1/2" Red PEX Tubing (100 ft Coil):

Very easy to use no fitting for corners. Easy to bend like all pex.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

1/2/2012
 
4.0

Excellent quality and pricing

By Kaz

from Tehachapi, CA

Verified Buyer

Comments about 1" Blue PEX Tubing (100 ft Coil):

main water buss through (remodel) house. This is a tough material that I expect will out last me in house plumbing. However, installing in cold weather (10 to 50 degree F) makes stiffness hard to handle. If possible leave in conditioned (heated) space for a few days before using.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

12/12/2011
 
5.0

Great to work with

By Copperless

from Knoxville, Tennessee

Verified Buyer

Comments about Rifeng 3/4" Blue PEX Tubing (300 ft Coil):

I have been an old school plumber my entire 25 years in the construction industry and have always used copper. I have to admit that after using this product that has all changed. It was very easy to use and time saving. The products were all perfect with no defects. I will be using this product again soon!

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

12/8/2011
 
5.0

I'll be back for more

By Nate

from Detroit, MI

Verified Buyer

Comments about 1" Blue PEX Tubing (100 ft Coil):

First time DIY pex plumbing rework on old home. Used 1" to replace the 3/4" copper, and 1/2" on all runs from the manifold. I've worked with pvc and copper. 1" Total pain to bend and work with. 1/2" not so much after getting used to it. Our kitchen contractor installed 1/2" Zurn pex. The 1/2" Rifeng was very similar. I was thinking all pex was created equal, but I ran short on 1/2" and got a couple of rolls of Sharkbite from [@]. There was no comparison. I'll be replacing that run with more Rifeng.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

11/27/2011
 
5.0

Just like the wholesale house

By greenhouse guy

from Summerville, SC

Verified Buyer

Comments about Rifeng 3/4" Red PEX Tubing (100 ft Coil):

Designing a hot water circulating system in my greenhouse. Will use Buck Stove with heat exchangers mounted above firebox and strapped to sides of firebox to heat water, and then move with circulating pump throughout plant area. Also using the same old heat exchangers salvaged from previous low pressure hot water system in the greenhouse itself.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

11/7/2011
 
4.0

good for long distance

By Vishal

from Niagara Falls, NY

Verified Buyer

Comments about Rifeng 1/2" Red PEX Tubing (300 ft Coil):

It ran awesome , the only toruble i had with it was unwinding it. i wish they would have a simpler way to unwinde it.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

10/26/2011
 
5.0

pex

By Jim

from NY

Verified Buyer

Comments about 3/4" Blue PEX Tubing (100 ft Coil):

Shipped fast

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

10/1/2011
 
5.0

simple to use

By gizzmo

from ranger tx.

Verified Buyer

Comments about Rifeng 1/2" White PEX Tubing (100 ft Coil):

have used the 1/2" line to repare water leaks under my house and now replaceing all my old water line with pex line. you don't have to worry about glue drying or anything ..just cut to lengh that you want, put a shark bit fitting and be done with it.

Bottom Line Yes, I would recommend this to a friend

Was this review helpful? Yes / No

 - You may also flag this review

Displaying reviews 1-10

Back to top

Previous | Next »

Q&A: Ask the Questions, share answers

Do you have questions about this product?

get answers from real customers and in-house experts with AnswerBox.

103 Questions | 142 Answers
Displaying questions 1-10Previous | Next »
  • 1" White PEX Tubing (100 ft Coil)

    Q:

    What size of pex should be used to run 100' from house to garage?
    Asked on 4/30/2012 by jb

    2 answers

    • VERIFIED BUYER

      A:

      If you only want water for occasional cleanings, etc. ¾” should do it. If
      you anticipate more volume needs, I would go with 1”.
      WKM

      Answered on 4/30/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      1' White

      Answered on 4/30/2012 by Another PexSupply Customer
  • 3/4" Red PEX Tubing (300 ft Coil)

    Q:

    Can any brand of Pex A tubing be used with ProPex expansion fittings or do I have to use only Aquapex A tubing for ProPex expansion fittings?
    Asked on 4/22/2012 by Tom from North East Wisconsin

    2 answers

    • CUSTOMER CARE

      A:

      You can use any brand of PEX-A tubing with ProPEX expansion fittings, but keep in mind that Rifeng tubing is PEX-B and AquaPEX is the only type of PEX-A plumbing PEX that we currently sell.

      Answered on 4/23/2012 by PexSupply Staff from NY

    • VERIFIED BUYER

      A:

      It is my opinion that you can use any brand Pex A tubing with the ProPex
      fittings. Good luck.
      WKM

      Answered on 4/23/2012 by Another PexSupply Customer
  • 1/2" Blue PEX Tubing (100 ft Coil)

    Q:

    What is maximum temperature for pex tubing?
    Asked on 4/19/2012 by Daniel from San Jose, CA

    5 answers

    • VERIFIED BUYER

      A:

      up to 200' def. F. if the pressure is less thn 80psi.

      Answered on 4/25/2012 by Another PexSupply Customer

    • CUSTOMER CARE

      A:

      Rifeng PEX is rated up to 180°F at 100psi.

      Answered on 4/20/2012 by PexSupply Staff from NY

    • VERIFIED BUYER

      A:

      The maximum temperature rating varies among manufacturers and the individual product lines they each create.
      In addition, the max temp decreases as the max pressure increases.
      Wirsbo Ex:
      Rating: 73.4 degrees F at 160 psi, 180 degrees F at 100 psi, and 200 degrees F at 80 psi
      You should find this rating printed on the PEX.

      Answered on 4/19/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      180 degrees is the recommended high end range

      Answered on 4/19/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      For plumbing, PEX is limited to 180° F

      Answered on 4/19/2012 by Another PexSupply Customer
  • 3/4" Blue PEX Tubing (100 ft Coil)

    Q:

    pressure rating on pex tubing systems
    Asked on 4/16/2012 by Tom from Williston nd

    2 answers

    • VERIFIED BUYER

      A:

      Typically the rating is:
      80psi @ 200 degrees
      100psi @ 180 degrees
      145psi @ 73 degrees
      You should check with the manufacturer for specifics. I cant tell you how far i have pushed it, but i can tell you there is a HUGE safety margin built in!!
      Sent from my iPhone

      Answered on 4/16/2012 by Another PexSupply Customer

    • CUSTOMER CARE

      A:

      PEX tubing is rated up to 160psi at 73°F, 100 psi at 180°F, and 80 psi at 200°F.

      Answered on 4/16/2012 by PexSupply Staff from NY
  • 1/2" Red PEX Tubing (100 ft Coil)

    Q:

    Installing all new plumbing in an older home. Would there be an advantage using Pex-A or Pex-B?
    Asked on 4/14/2012 by Billy from Ohio

    2 answers

    • CUSTOMER CARE

      A:

      PEX-A tubing has better shape recognition. This makes it more flexible, freeze-resistant and easier to work with. You can fix kinks in PEX-A with by applying heat. Only PEX-A tubing is compatible with expansion-type fittings. PEX-B tubing is generally less expensive, and either type of tubing is appropriate for most applications.

      Answered on 4/16/2012 by PexSupply Staff from NY

    • VERIFIED BUYER

      A:

      That's a complicated question. More flexibility would definitely be preferable
      when plumbing and older structure. However a proprietary expansion connection
      system can be cost prohibitive and also possibly undesirable in colder climates.
      Pex-B is the more affordable, however the rigidity is more difficult from every
      aspect especially as the size increases.
      I can make one recommendation with this limited amount of information. If an
      insulated tube is desirable for a hot run to a dishwasher for example. Paying
      the extra for insulated pipe is a good idea, in my opinion. The R factor is much
      greater with factory insulated pipe.
      I personally needed both for working on my projects.
      Hope this has a benefit to you.

      Answered on 4/14/2012 by Another PexSupply Customer
  • 3/4" White PEX Tubing (100 ft Coil)

    Q:

    CAN BLUE PEX AND WHITE PEX BE USED FOR THE SAME UNDERGROUND WATER SUPPLY LINES IN RESIDENTIAL USAGES?
    Asked on 4/10/2012 by JOSE from ATLANTA, GA

    8 answers

    • VERIFIED BUYER

      A:

      So long as the white pex is approved for "potable water" I see no problem!

      Answered on 4/13/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes. There is no difference in the two other than the color.

      Answered on 4/13/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      I never used either of these pex products for underground. I normally use the black well pipe which is similar to pex but much thicker and designed for direct burial.
      Hope this helps.
      Mark

      Answered on 4/13/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes, Pex is rated for direct burial. It should be buried in a small stone,
      sand bed and below the frost line. I placed mine inside a PVC conduit so if
      later replacement is ever necessary, I won't have to redig the trench.

      Answered on 4/13/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      The questions "supply line" sounds like a potable requirement.
      Blue (and red) PEX are usually marked and marketed for potable applications while white is PEX is often marked and marketed for non-potable. If light can reach the water, algae will grow.
      Safest bet is to check the temp and pressure ratings of the PEX to match your application. If the application requires potable, contact the manufacturer. An underground line would be a hard problem to solve down the road.

      Answered on 4/13/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      The coloring of pex is done to make it easier to identify cold water lines vs. hot water lines. Otherwise, there is no difference in the application of colored pex vs. non-colored pex. The usage of pex outdoors and the burying of pex is governed by your local building department - you should contact your building inspector to determine the permitted usage for your location. They may also suggest a better alternative material to use - flexible PVC, copper, etc.
       

      Answered on 4/11/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes!
      Sent from my Verizon Wireless 4GLTE smartphone

      Answered on 4/10/2012 by Another PexSupply Customer

    • CUSTOMER CARE

      A:

      They can. The colors on PEX tubing have nothing to do with their ratings or approved uses. The red and blue colors make it easier to identify hot and cold lines, but you can use red for cold, blue for hot, and any color for the supply line.

      Answered on 4/10/2012 by PexSupply Staff from NY
  • 3/4" Blue PEX Tubing (100 ft Coil)

    Q:

    Can shark bite fittings be used with PEX Tubing?
    Asked on 3/28/2012 by Glenn from Allentown,Pa

    15 answers

    • VERIFIED BUYER

      A:

      Yes you can.

      Answered on 3/29/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      They fit just fine. if you look on the package they show the approval. I've
      used the with no issues.
      Robert Landry

      Answered on 3/28/2012 by sailingromantic from custer Wa

    • VERIFIED BUYER

      A:

      Yes, Shark Bite fittings may be used with PEX Tubing. I personally prefer the crimp ring method due to the cost of the Shark Bite fittings but that does require a crimper. Sare easy and work very well if you can justify the cost.
      Question: "Can shark bite fittings be used with

      Answered on 3/29/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes

      Answered on 3/29/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      I believe that sharkbite fittings can be used with PEX.
      Sharkbites can be awesome in some situations to get you out of a jam without any soldering or hassles and without buying pex crimping tools. But I am cautious about where I use a... always keeping in mind that a plumbing failure can cause a serious flood... and go on for hours or days before someone discovers it. I use sharkbites confidently in situations where the fitting is unlikely to geted or pulled at an angle by movement of the piping.
      But pex piping tries to coil-up and move around, which will inevitably cause it to pull the on the unevenly. It might hold just fine, but I would not "bet the farm" that a sharkbite will hold in this situation. A more positive connection to the pex would make me more confident. Such as a fitting that gets crimped to the pex and is then connected to another pipe by soldering, threading, or compression.
      Sharkbites are also pricey, so it you need several of fittings, you will be spending enough $$ to be well on your way to buying a crimp tool.
      To explicitly answer your question, yes, there are sharkbites made that will connect to pex. I just removed a sharkbite today that I had used to connect to a 3/4 inch copper line to 3/4" pex. I put it in several months ago and it worked just fine until we got around to made bigger modifications. When you use a sharkbite with pex, I believe that there is a little doohickey that goes INSIDE of the pex pipe to keep it rigid inside of the sharkbite. This doohickey is not required with copper, for example. Make sure that you have no burrs or anything that will buger the o-ring inside of the sharkbite. Read the label to make sure that it is intended for pex. And made sure that all pipes are fully inserted in to the sharkbite fitting. We don't want no stinking flooding.
      Happy pexing.
      John Westney

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes, I have used them several times. Remember to mark your stab depth on the pex pipe prior to stabbing. Good luck.

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yep. And copper and CPUs.
      Sent from my iPad

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes. I have found that they work great, however, you have to make sure the pipe goes straight into them, and you clamp it so that there is no "side" load on the fitting, or it could leak just a little.

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Shark bite fittings worked perfectly on my pex project.  I built my own hot and cold manifolds with soldered copper then ran everything off of there with pex and shark bites.  T he fittings press right on and can be released easily with a small plastic u-shaped tool if necessary.  I don't know how they work but it's like magic!  The same shark bite connector works  on both copper pipe and pex!  I will use shark bites for everything from here on out!  Pex Supply i s the place to shop on-line.  The web site navigates easily, the prices are reasonable and everything was delivered faster than expected.  You can't go wrong with Pex Supply!
      Patrick Murray

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes I used them in my basement shower install. Worked great

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes. They work well. Simply make a clean, square cut on your pex and then
      push the pex into your fitting about 1". That is it.

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes, shark bite fittings can be used, but in my opinion, it would not be
      cost effective. These fittings would be a good way to join pex to copper or
      cpcv if you need to.
      WKM

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Yes. I used them in plumbing my house. Quite a bit more expensive, but they
      work fine.

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      Absolutely.....that's the beauty of sharkbite. One fitting that solves many
      problems.
      "Can shark bite fittings be used with PEX Tubing?"

      Answered on 3/28/2012 by Another PexSupply Customer

    • CUSTOMER CARE

      A:

      SharkBite fittings can be used with any standard PEX tubing, including the Rifeng brand.

      Answered on 3/28/2012 by PexSupply Staff from NY
  • 1" White PEX Tubing (100 ft Coil)

    Q:

    can this be used inplace of 1" pvc on a pump up toilet (Sanicompact) discharge line.
    Asked on 3/23/2012 by Peter from Wakefield NH

    7 answers

    • VERIFIED BUYER

      A:

      very simply....yes....

      Answered on 3/28/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      If the manufacturer permits use of a 1" pvc discharge line, then yes this 1" pex could be used in its place--following the manufacturer's specifications of maximum length.

      Answered on 3/25/2012 by LeeRen from Utah

    • VERIFIED BUYER

      A:

      Absolutely yes!
      Sent from my Verizon Wireless 4GLTE smartphone

      Answered on 3/24/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      I don't see why you couldn't.

      Answered on 3/24/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      not sure, would default to the UL Listing and see if it is listed as a
      Drain, Waste, Vent pipe. also would think that the ID is too small.

      Answered on 3/24/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      If the inside diameter of the pipe is 1" there is no reason
      why you could not use it. However you will need a shut-off
      valve and a swing-check on the vertical riser from the tank.
      You may also have difficulty in maintaining "pitch" when you
      switch from the verical (riser) to the horizontal (header) part
      of the drain age system. You need to maintain 1/4" per foot
      of pitch minimum on the horizontal.
      Local codes may prohibit the use, but personally I see no reason why not!

      Answered on 3/23/2012 by Another PexSupply Customer

    • VERIFIED BUYER

      A:

      I don't know. I can tell you it it being used to feed into and out of my water heater post pressure control valve and post expansion tank. I hope this helps you. I redid the plumbing of my entire 3 bedroom 3 bathroom house. I'm very happy with the product.

      Answered on 3/23/2012 by Another PexSupply Customer
  • 3/4" Blue PEX Tubing (100 ft Coil)

    Q:

    Is there a reason or purpose for the different colors of PEX Tubing?
    If so, what are they?
    Asked on 3/4/2012 by JAMES09 from JOPPA MD

    1 answer

    • CUSTOMER CARE

      A:

      The only purpose is to make things easier for installers and homeowners. Blue PEX and red PEX can be used to differentiate between cold and hot lines for plumbing, but there is nothing about the tubing that would prevent you from using red PEX for all the lines.

      Answered on 3/5/2012 by PexSupply Staff from NY
  • Rifeng 3/4" Blue PEX Tubing (300 ft Coil)

    Q:

    Is there 200PSI rated tubing for compressed air?
    Asked on 2/27/2012 by Anonymous

    1 answer

    • CUSTOMER CARE

      A:

      Unfortunately, there is no PEX tubing that is rated for use with compressed air.

      Answered on 2/28/2012 by PexSupply Staff from NY
Displaying questions 1-10Previous | Next »

Do you have a question about this product? 

Free Shipping on orders over $300

You May Also Want

PexSupply.com Logo

Join Our Mailing List - Sign up and receive special offers and coupons

Nextag Seller PriceGrabber User Ratings for Pex Supply PHCC BBB Reliability Seal
HACKER SAFE certified sites prevent over 99.9% of hacker crime. Facebook Twitter Youtube